AL 600

The AL 600-T is a universal wire-dereeler process for heavy coils.

The dereeler is equipped with pneumatic device dancers, which realizes a smooth trigger wire sensors.
The coil is connected by two pneumatic clamping taper-fixed nerves. The recording width is max. 600mm.
The wire expiry is connected to a variety of take-up unit-coupled devices, where it is determined by the speed of the winding reel.
He is using hollow profiles made ??mainly of welded construction.

AU 600

au-600_en

AU 800

AL 750

The AL 750 is a general purpose driven wire pay-off for heavy coils.
The drain is equipped with an emergency-stop button, which causes immediate shutdown of the sequence and the winder when pressed during operation.

The coil is rolled over a roller bridge in the loading position. The bridge serves as a pick and place, as he lifts the hand lever the coil in the clamped position. The sleeves are adjustable in height for different coil diameters. Similarly, the Rollsteg is the respective coil diameter is compensated.

The pay-off can be coupled with a variety of take-up devices, with him, the winding speed is specified by the winder.
The sequence AL 750 can also be operated in conjunction with a separate memory dancers.

It is carried out using hollow sections mainly as a welded structure.

AL 850

The AL 850 is a general purpose, pneumatically braked pay-off for large layer coils.
The proportions may be changed according to customer requirements.

The brake is externally switchable.

The pay-off can be coupled with a variety of take-up devices, with him, the winding speed is specified by the winder.

The sequence AL 850 can also be operated in conjunction with a separate memory dancers.

It is carried out using hollow sections mainly as a welded structure.

AS 2

AS 2duo

AS-5

AS 7

AS 400

The AS 400 is a general purpose driven flow with adjustable wire or thread tension.
The sequence AS 400 can only be operated in conjunction with a separate memory dancers.

It is carried out using hollow sections mainly as a welded structure. The area of the coil is covered with a protective grating, whose opening during the operation of the instant
Stopping the sequence and causes the rewinder (E-STOP).

The unwound coil is driven by a frequency-controlled AC motor via a poly-V-belt. The speed of the motor depends on the winding speed specified by the winder.
The setting of the strand tension is conducted on the dancers memory.

It is coupled with a variety of take-up devices, with him, the winding speed is specified by the winder.

AS 600

The material to be winded is slided on a ball-beared central shaft. Therefore you have to observe the following points:

The central shaft is taken out completely from the bearings and the cone which is opposite to the brake system is to be slided off (loose the screw).

The coil and the cone are to be slided on. Put the central shaft into both bearings below. After that the flats of bearings are to be closed and the screw of the cone is to be tightened.
All parts of the dereeler are corrosion resistant in order to give it enough power for a long working life.

AS 2000

The AS 2000 is a universally suitable driven dereeler with an adjustable wire or thread tension.
It can be coupled with several re-winding units whereas the winding speed is determined by the re-winder.
The machine will be produced with the well-tried quality of Froitzheim & Rudert.
All parts of our machines are corrosion resistant. All drives have enough power for a long working life even under hardest operational conditions.

ASP 12

ATM 2

The process ATM 2 is based on the basis of multiple sequence frame ATM12.
A constant wire pull-off force is realized via a spring-loaded dancer system and an electronically controlled brake system. As a rule, hysteresis brakes are used. The dancers position is opto-electronically recorded (optical sensor, distance measurement) and transferred to the brake control system and a corresponding braking power generated.
The controlled brake system provides high Umspulgeschwindigkeiten at high Spulqualität.
(Braked all execution units present in use to be) in the case of a wire break or at the end of the wire via a wire circuit plan a quick stop.
A "EMERGENCY STOP", realized by rewinding machine is carried out via a permanent magnet brake.

ATM 2spezial

ATM 12

The dereelers ATM 8-12-16 are multiple flow racks, with up to 16 designed as a compact assembly single discharge points. Each run unit operates as a separate system. Thus, up to 16 individual wires combined into one compartment and rewound be (number of strands of multiple arbitrary).

A constant wire pull-off force is realized via a spring-loaded dancer system and an electronically controlled brake system. As a rule, hysteresis brakes are used. The dancers position is opto-electronically recorded (optical sensor, distance measurement) and transferred to the brake control system, and a corresponding braking current is generated.

The controlled brake system provides high winding speeds with sufficient qualaty.
In the case of a wire break or wire end via a wire circuit, the machine indicates a quick stop.
A "EMERGENCY STOP" is produced by a permanent magnet brake.

ATM 16

The dereelers ATM 8-12-16 are multiple flow racks, with up to 16 designed as a compact assembly single discharge points. Each run unit operates as a separate system. Thus, up to 16 individual wires combined into one compartment and rewound be (number of strands of multiple arbitrary).

A constant wire pull-off force is realized via a spring-loaded dancer system and an electronically controlled brake system. As a rule, hysteresis brakes are used. The dancers position is opto-electronically recorded (optical sensor, distance measurement) and transferred to the brake control system, and a corresponding braking current is generated.

The controlled brake system provides high winding speeds with sufficient qualaty.
In the case of a wire break or wire end via a wire circuit, the machine indicates a quick stop.
A "EMERGENCY STOP" is produced by a permanent magnet brake.

ATM 550

The dereeler ATM 550 is a powered wire unwinding frame for large coils of wire.
A constant wire pull-off force is realized via a spring-loaded dancer system and an electronically controlled brake system. As a rule, hysteresis brakes are used. The dancers position is opto-electronically recorded (optical sensor, distance measurement) and transferred to the brake control system and a corresponding braking power generated.
The controlled brake system provides high Umspulgeschwindigkeiten with sufficient Spulqualität.
In the case of a wire break or wire end via a wire circuit plan a quick stop.
A "EMERGENCY STOP" is produced by a permanent magnet brake.
The total wire run is surrounded by a safety cage. The wrapping is done only when the cage is closed properly!

DF 100

Overhead wire dereelers of the DF series are used for trouble-free feeding of the wire to the machine.
For this purpose, you have a braking system and a dancer for tension control.
The DF 100 may be for wires with a diameter 0.04 to 0.3 mm.

DF 200

Overhead wire dereelers of the DF series are used for trouble-free feeding of the wire to the machine.
For this purpose, you have a braking system and a dancer for tension control.
The DF 100 may be for wires with a diameter 0.2 to 0.9 mm.

DF 300

Overhead wire dereelers of the DF series are used for trouble-free feeding of the wire to the machine.
For this purpose, you have a braking system and a dancer for tension control.
The DF 100 may be for wires with a diameter 0.5 to 2.0 mm.

DF 310

Overhead wire dereelers of the DF series are used for trouble-free feeding of the wire to the machine.
For this purpose, you have a braking system and a dancer for tension control.
The DF 100 may be for wires with a diameter 0.5 to 2.0 mm.
To make it easier, manual wire tightening, e.g. Pull the loop or New Creation of the wire to a bobbin, this dereeler includes an integrated pneumatic strain relief. This can be controlled from the machine. An adjustable pressure maintenance unit for compressed air supply is included.

DF 450

Overhead wire dereelers of the DF series are used for trouble-free feeding of the wire to the machine.
For this purpose, you have a braking system and a dancer for tension control.
The DF 100 may be for wires with a diameter 1.5 to 3.0 mm.
To make it easier, manual wire tightening, e.g. Pull the loop or New Creation of the wire to a bobbin, this dereeler includes an integrated pneumatic strain relief. This can be controlled from the machine. An adjustable pressure maintenance unit for compressed air supply is included.

EDAZ 1

The EDAZ 1 is an electronically controlled wire pull which is particularly suitable for very fine wires.
A constant wire pull-off force is realized via an electronically controlled brake system. As a rule, a hysteresis brake is used.
The controlled braking system allows a precisely constant tensile force and thus a high winding quality.